HomeMy WebLinkAboutCorrespondenceþr,rutn 4"","þngb"t ,\m to navigate items
Jeff Dunn <jeff@lindauerdunn.com >
Thu 6/15/2017 1:48 PM
ro:Bobby Dorssey < bobby@buildwithrm.com >;
2 attachments (399 KB)
Page 175 from c-c-2015.pdf; Page 176from c-c-2015.pdf;
Bob,
As we discussed, as an alternate to the fabricated steel hangers shown on the drawings, simpson face
mount hangers may be used with connections to the concrete walls by the Simpson Titen screws, as
shown on the attached pages from the Simpson catalog.
The HU410 hangers can be used forthe double L.V.L. beams, and type HU612 hangers can be used for
thetriples. UsethesamescrewpatternfortheHU6l2'sasislistedfortheHU4l0's.
Jeff
Jeff Dunn
Principal
Lindauer Dunn, lnc.
Structural Engineers
802 Rood Avenue, Grand Junction, CO 81501
(97 0) 241 -0900 Fax (97 0) 243-2430
ieff@lindauerdunn.com
www.lindauerdu nn.com
message
list
Þunn 1of7
HU/HUG/HSUR/t Hansers
ùlasonry Conaecton
HU and HUC products are heavy duty face mount ioist hangers made from 14 gauge
galvanized steel.. The HUC is a concealed flange version of the HU. Concealed llange hangers
have the header flanges turned ln.
. HtJ is available with header flanqes concealed, provided the W dimension is 2%0" or
greater, at 100% of the table load. Specify HUC.
. HU is available with one header flange concealed when the W dimension is less than
2s/ta" al 100% of the table load.
. For allowable loads on HU products not listed in the table, request technical bulletin
T-HUHUCTTN.
MATERIAL: 14 gauge
FlìllSH: Galvanized, ZMAX@ and stainless steel available
IÌ{STALLÀT|0N: . These hangers are attached t0 grouted CMU walls using %"x2%" hex
head Simpson Strong-Tie@ Titen@ screws or for concrete walls using l¿"x13/i' hex
head T¡ten screws. Tten screws aro not provided.
. Drill the %e' diameter hole t0 the specified embedment depth plus %".
. Alternatively, drill the %0" diameter hole to the specitied embedment depth and
blow it clean us¡ng compresssd air.
. Caution: oversized holes in the base material will reduce 0r eliminate the
mechanical interlock of the threads w¡th tho base material and wlll reduce the
anchor's load capacity.
. The hang8rs should be installed such that a min¡mum end and edge distance of
1%'is maintained.
. Provide moisturs banier bstween beam and wall per iurisd¡ctional requirements.
G0DES: See page 12 for Code Reference Key Chart.
F t[ffiìt
-T
I
ft
tV
Concealed tlanges
govern.
C90 units and type N or S monar
HU612 for the triple
11 718" L.V.L.
HHU4ll¡
HUC410
Model
No.
D¡mensions Faslener$Allowable Loads (0F/SP}
Goda
Rol.w H CMU Goncrete Joist Uplill 0own
{1601 (100/r15/125ì
HU26 lYta Slts 21/t 4-ltx?/tTiløn 4-t/cx13/¿'lilen 2-10dx114 290 1545
170
HU283 1e/ta 5Y4 2Y4 6-%x2Vtfiløn 6-%x1Y¿Iilan 4-10dx11,1 575 2400
HU21()1s/tt 7Ys 2Y4 8-l¿x23/¿Ïilen 8-t/tx13/tlilen 4-10dx11/z 575 2400
HU46 3s/tø 53/tø 2:/,12-/tx23/clilen 12-Y4\13/4'Íilen 6-10d 1085 3950
HU26-2 3)/s 5YB 2h 12-Y4XZY4Iiten 12-Y4x1Y4frtan 6-10d 1085 3950
HU48 3%a 61Ttø 2tÁ 14-1/¿x2Y¿Titen 14:Áxl7qIiten 6-10d
6-10d
1085
1085
4350
4350HU2B-2 3Ys 7 214 1 -Yqxf/cfilen 14-/cx13/¿Tilen
HU4lO 3e/ta 85/a zVr 18-/tx23/qlilen 18'1/¿x13/¿\ßn 10-10d 1810 5085
HU210-2 ?ttÁ 81/'s zl,t 18-1/tx2YcIilen 18-Y1x1Y1Titen 10-10d 1810 5085
HSUR/l26-2 3l/g 416/ta 27/tø 12-Ux2Y4Tilen 12-Y1x'13/1Iiløn 4-16dx21Á 815 2625s
FÈÈe
Cì
C¡
=¡ÈÞ
G¡a
IIItIIIDIfN
ôuts
=ÉÀ
oz
z
=oou
FozoÉF
zo
=
@
oa
1.
2.
3.
4.
Uplift loads have been increased for w¡nd or earthquake loading with no furthel iflcrease is allowed. Reduc6 where other loads
M¡nimum concrete strength I'c shall be 2500 psi. CMU shall havs a minimum grout strength of 2500 psi wlth standard ASTM
The HU28 can be ordered skowed 45'and achiev€ the same loads.
See page 173 for Tten screw information. Use stainless-stesl Titen@ screws and products in exposed applications.
Tabulated loads apply to stainless-steel applications.
Noted loads tor the HSUH/I shall be 0.8 the table loads for concrele applications.
Table allowable loads were determinsd using tested lowest ultimale/3 or fastener calculation values.
llAlLS: l 6dx2% = 0.162' dla. x 2%' long, 1 0d = 0.1 48' d¡4. x 3' long,
10dx1% = 0.148" dia. x 1/2" long. See pages 22-23 for other nail sizes and information.
5.
6.
7.
1w
lV+
hin
HU410 lnstalled on
Masonry Block Sldewall
HSUR/t26-2 Inslalled on
Masonry Block Sidewall
HUC410 lnstalled on
Masonry Block End Wall
1,Ê
min
175