Loading...
HomeMy WebLinkAboutOWTS Design Report 09.10.201933 Four Wheel Drive Rd Carbondale, CO 81623 970409.5259 September 10, 2019 Project No. C1469 Shane David s.david@davidelectric.us Subsurface Investigation and Onsite Wastewater Treatment System Design 5 -Bedroom Residence 422 CR 162 Garfield County, Colorado Shane, ALL SERVICE septic, LLC performed a subsurface investigation and completed an onsite wastewater treatment system (OWTS) design for the subject residence. The 6.118 -acre property is located outside of Carbondale, in an area where OWTSs are necessary. Legal Description: Section: 29 Township: 7 Range: 87 Subdivision: STIRLING RANCH PUD Lot: 21 Parcel ID: 2391-292-05-021 SITE CONDITIONS A 2 -bedroom residence is developed on the property and is currently served by an existing OWTS. We were unable to find any record of the OWTS in Garfield County Community Development's database. There is a desire to remodel the residence and the OWTS will be upgraded to accommodate a total of five bedrooms in the residence. A well serves the property potable water. The well is located off-site and is shared between several homes. The well is located greater than 100 -feet form the proposed soil treatment area (STA) and greater than 50 -feet from the proposed septic tank. The proposed soil treatment area (STA) is located to the west of the residence. The area is covered with native grasses. The area has an approximate 5% slope to the west. There should be no traffic or staging of material over the future STA site to avoid compaction of soils prior to construction of the STA. SUBSURFACE The subsurface was investigated on August 22, 2019 by digging three soil profile test pit excavations (Test Pits). A visual and tactile soil analysis was completed by Carla Ostberg at the time of excavation.' The materials encountered in the Test Pit #1 consisted of light brown, dense sandy clay to 7.0 -feet, underlain by tan, dense sandy clay to a maximum depth explored of 8.0 -feet. No bedrock or groundwater was encountered. ' Carla Ostberg holds a Certificate of Attendance and Examination from the CPOW Visual and Tactile Evaluation of Soils Training. Page 2 The materials encountered in Test Pit #2 consisted of dark brown clay loam topsoil to 3.0 -feet, underlain by tan, dense sandy clay where practical digging refusal was encountered. No bedrock or groundwater was encountered. The materials encountered in Test Pit #3 consisted of light brown, dense sandy clay to 3.0 -feet, underlain by tan, dense, sandy clay to maximum depth explored of 7.0 -feet. No bedrock or groundwater was encountered. A tactile analysis of the soils was taken from Test Pit #3 at 2 -3 -feet below grade. Soil structure grade below was weak. The soil formed a ball and a ribbon less than 1 -inch in length before breaking. Soil structure shape was single -grain to blocky and consistence was loose to friable. Soil texture was both gritty and smooth. Soils are consistent with Soil Type 2A. Sandy clay in the Missouri Heights area has a low placidity index. A long term acceptance rate (LTAR) of 0.5 gallons per square foot will be used to design the OWTS. Sidewall (weak structure grade) sieved sample Page 3 Backfill View of Test Pits #1 and #3 DESIGN SPECIFICATIONS The existing OWTS serving the residence be abandoned. The septic tank must be pumped and the sides crushed, top, and bottom crushed and the void filled with onsite material or removed. The existing STA may be abandoned in place. Design Calculations. Average Design Flow = 75 GPD x 2 people/bedroom x 3 Bedrooms + 150 GPD (4th and 5th bedrooms) = 600 GPD LTAR = 0.5 GPD/SF 600 GPD / 0.5 GPD/SF x 0.8 (pressure dosed trenches) x 0.7 (chambers) = 672 SF The new OWTS design is based on 5 -bedrooms. An average daily wastewater flow of 600 GPD will be used. For the purposes of this OWTS design, Benchmark Elevation has been established as 100' as the existing sewer line exiting the residence. ALL SERVICE septic, LLC should be notified of any discrepancies or problems with grade elevations of proposed components during installation of the OWTS. Page 4 OWTS Component Minimum Elevation Primary Tank Inlet Invert 98' _ Automatic Distributing Valve 99' Infiltrative Surface 98' If the existing sewer line will remain in use, it should be explored to assure it is in good condition. If found to be in poor condition or cast iron, it should be replaced. The 4 -inch diameter (SDR -35 recommended) sewer line exiting the residence must have a double -sweep clean out and a minimum 2% grade to the septic tank. The system installation must include A 2000 -gallon, two-compartment Valley Precast concrete septic tank with an Orenco® ProPak and PF3005 pump in the second compartment of the septic tank. The floats must be set to dose approximately 60 gallons each pump cycle, allowing for approximately 1 gallon of drain back into the pump chamber after each pump cycle. Risers must be installed on the septic tank to bring access to grade. Handle extensions on both the effluent filter and float tree must be installed if the riser height exceeds 1 -foot. The control panel must be located within line of sight of the septic tank. We recommend Valley Precast out of Buena Vista perform start up on the pumping system. Pump lines (1.5 -inch diameter Schedule 40) must be installed from the pump to an Orenco® automatic distributing valve (ADV), model 6404. This pump line must have a minimum 1% grade for proper drain back into the tank after each pump cycle. The ADV must be placed at a high point in the system and be placed in an insulated riser with access from grade. Screened rock must be placed below the ADV to support the ADV and to assure the clear pipes exiting the ADV remain visible for future inspection and maintenance. Effluent will be pressure dosed through 1.5 -inch diameter pipes to four trenches, each with 14 `Quick 4' Infiltrator® chambers, for a total of 56 chambers and 672 square feet of infiltrative area. There must be at least 4 -feet of undisturbed soil between each trench, although we recommend at least 6 -feet. Effluent will be pressure dosed to 1.5 -inch diameter laterals, which must be hung with zip ties from the underside of the chambers. Laterals will have 5/32 -inch diameter orifices facing up, with the exception of the first and last holes facing down for drainage. Orenco® Orifice Shields may be placed under each downward - facing orifice. The orifices must be placed 3 -feet on center. Each lateral must end in a 90 degree ell facing up with a ball valve for flushing. Valves may be placed in a valve box, accessible from grade, for access. Inspection ports must be placed at the beginning and end of each trench. Ports may be cut to grade and covered with a valve box for access. The component manufacturers are typical of applications used by contractors and engineers in this area. Alternatives may be considered or recommended by contacting our office. Construction must be according to Garfield County On -Site Wastewater Treatment System Regulations, the OWTS Permit provided by Garfield County Building Department, and this design. INSTALLATION CONTRACTOR ALL SERVICE septic, LLC expects that the installer be experienced and qualified to perform the scope of work outlined in this design. The installer must review this design thoroughly and coordinate with our office in advance of installation. Any additional conditions in this design or county permit must be completed and documented prior to final approval of the OWTS installation. Communication between the installer and this office is expected throughout the installation. Page 5 INSTALLATION OBSERVATIONS ALL SERVICE septic, LLC must view the OWTS during construction. The OWTS observation should be performed before backfill, after placement of OWTS components. Septic tanks, distribution devices, pumps, dosing siphons, and other plumbing, as applicable, must also be observed. ALL SERVICE septic, LLC should be notified 48 hours in advance to observe the installation. In an effort to improve the accuracy of the record drawing, we request that the installer provide a sketch of the installation, including path of the sewer lines, water line installation (if applicable), septic tank location, STA location, and measurements from building corners or another fixed objects on the property. This sketch is most easily provided on Sheet W2.0 of the OWTS Design Packet. Photographs of the installation and final cover are also requested to supplement our installation documentation. REVEGETATION REQUIREMENTS An adequate layer of good quality topsoil capable of supporting revegetation shall be placed over the entire disturbed area of the OWTS installation. A mixture of native grass seed that has good soil stabilizing characteristics (but without taproots), provides a maximum transpiration rate, and competes well with successional species. No trees or shrubs, or any vegetation requiring regular irritation shall be placed over the STA. Until vegetation is reestablished, erosion and sediment control measures shall be implemented and maintained on site. The owner of the OWTS shall be responsible for maintaining proper vegetation cover. OPERATION INFORMATION AND MAINTENANCE The property owner shall be responsible for the operation and maintenance of each OWTS servicing the property. The property owner is responsible for maintaining service contracts for manufactured units, alternating STAs, and any other components needing maintenance. Geo -fabrics or plastics should not be used over the STA. No heavy equipment, machinery, or materials should be placed on the backfilled STA. Machines with tracks (not wheels) should be used during construction of the STA for better weight distribution. Livestock should not graze on the STA. Plumbing fixtures should be checked to ensure that no additional water is being discharged to OWTS. For example, a running toilet or leaky faucet can discharge hundreds of gallons of water a day and harm a STA. If an effluent filter or screen has been installed in the OWTS, we recommend this filter or screen be cleaned annually, or as needed. If the OWTS consists of a pressurized pump system, we recommend the laterals be flushed annually, or as needed. The homeowner should pump the septic tank every two years, or as needed gauged by measurement of solids in the tank. Garbage disposal use should be minimized, and non -biodegradable materials should not be placed into the OWTS. Grease should not be placed in household drains. Loading from a water softener should not be discharged into the OWTS. No hazardous wastes should be directed into the OWTS. Mechanical room drains should not discharge into the OWTS. The OWTS is engineered for domestic waste only. ADDITIONAL CONSTRUCTION NOTES If design includes a pump, weep holes must be installed to allow pump lines to drain to minimize risk of freezing. The pump shall have an audible and visual alarm notification in the event of excessively high water conditions and shall be connected to a control breaker separate from the high water alarm breaker and from any other control system circuits. manually operated. Excavation equipment must not drive in Extensions should be placed on all septic Backfill over the STA must be uniform and Page 6 The pump system shall have a switch so the pump can be excavation of the STA due to the potential to compact soil. tank components to allow access to them from existing grade. granular with no material greater than minus 3 -inch. LIMITS: The design is based on information submitted. If soil conditions encountered are different from conditions described in report, ALL SERVICE septic, LLC should be notified. All OWTS construction must be according to the county regulations. Requirements not specified in this report must follow applicable county regulations. The contractor should have documented and demonstrated knowledge of the requirements and regulations of the county in which they are working. Licensing of Systems Contractors may be required by county regulation. Please call with questions. Sincerely, ALL SERVICE septic, LLC Oft,(1(i i Carla Ostberg, MPH, REHS Reviewed By: Richard H. Petz, • 9/16/19 7.4oar Pump Selection for a Pressurized System -single Family Residence Project David Residence / 422 CR 162 Parameters Discharge Assembly Size Transport Lenglh Before VaNe Transport Pipe Class Transport Line Size Distributing Valve Model Transport Length After Valve Transport Pipe Class Transport Pipe Size Max Elevation LAS Manifold Length Manifold Pipe Class Manifold Pipe Size Number of Laterals per Cell Lateral Length Lateral Pipe Class Lateral Pipe Size Orifice Size Orifice Spacing Residual Head Flow Meter 'Add-on' Friction Losses 1.50 inches 12 feel 40 1.50 inches 6404 60 feet 40 1.50 inches 3 feet 20 feel 40 1.50 inches 4 56 Feet 40 1.50 inches 5/32 inches 3 feel 5 feet None inches 0 feet 300 250 200 I u- 0 :- Calculations m iD Minimum Flow Rate per Orifice 0.69 gpm = 150 Number of Orifices per Zone 19 9 Total Flow Rate per Zone 129 gpm Number or Laterals per Zone 1 E % Flow Differential 1st/Last Orifice 20 % ' CI Transport Velocity Before Valve 20 fps Transport Velocity After VaNe 2.0 fps ,S M Frictional Head Losses Lossthlough Discharge 0.5 feet Loss in Transport Before Valve 0.1 feet Loss through Valve 2.6 feel Loss in Transport after Valve 0.7 feet Loss in Manifold 0.1 feet Loss in Laterals 0.2 feet Loss through Flowmeter 0.0 feet 'Add-on' Friction Losses 0.0 feet Pipe Volumes Vol of Transport Line Before Valve 1.3 gals Vol of Transport Line After Valve 6.3 gals Vol of Manifold 2.1 gals Vol of Laterals per Zone 5.9 gals Total Vol Before VaNe 1.3 gats Total Vol After Valve 14.4 gals Minimum Pump Requirements Design Flow Rate 12.9 gpm Total Dynamic Head 12.2 feet Orenco 100 5 PumpData 10 15 20 25 Net Discharge (gpm) PF3005 High Head Effluent Pump 30 GPM, 1/2HP 115/230V 10 60Hz. 200V 30 601-lz PF3007 High Head Effluent Pump 30 GPM 3/4HP 230V 10 60Hz, 200/460V 30 60Hz PF3010 High Head Effluent Pump 30 GPM, 1HP 230V 10 60Hz, 200/460V 30 60Hz PF3015 High Head Effluent Pump 30 GPM, 1-1/2HP 230V 10 60Hz. 200/230/460V 30 60Hz Legend 30 35 System Carve: Pump Curve: Pump OptimaLGange: OperatiMlg Point: DesiPPoint: 40 WELL ON NEIGHBORING PROPERTY, GREATER THAN 100 -FEET FROM STA BASIS OF BEARING 10.00' UTILITY EASEMENT 811.15' 1U 2 UTLUI7' N90'00'00"1r 821.15• C/L 20' TRAIL ESAIT. SITE PLAN 0 1• - 50•-0° -- &71.'7- Rl rd -5 a1 COVERED STORAGE TRACK ROPOSED IMPROVEMENTS PROPERTY SURVEY. THE S THE HOMEOWNERS DUTY ID IMPROVEMENTS :TBACK DISTANCES SHOULD ION. 1ETBACK LT. 21 TP • �• P3 . ' TP # R + ar 'r F, , e' - . ' r STA ,15• SAWr�^ A ii> Lau/ 11 GI C m �[ OVERHEAD MLITT LINE I I E9 I ; FUTURE 5 -BEDROOM RESIDENCE 9.:- ay COV( DECD s GRAVEL DRIVE • 235 2' 11 6.1185 ACRES p • , VERED CENTERLINE WIVE 172.7' 13L -S' r 25.00' SETBACK -.-.--------- 590•00 ' CO"R 811.15' 1U 2 UTLUI7' N90'00'00"1r 821.15• C/L 20' TRAIL ESAIT. SITE PLAN 0 1• - 50•-0° 1.5" DIAM SCH-40 LINES TO EACH TRENCH (MIN. 1% FALL TO t TRENCHES) ADV MODEL 6404 AT HIGH POIN , ACCESSIBLE AT GRADE 1.5" DIAM SCH-40 PUMP LINE TO ADV (MIN. 1% DRAIN BACK TO SEPTIC TANK TP2� • EXISTING TANK D STA TO BE NDONED HAMBER TRENCHES. :S EACH WITH 14 CHAMBERS 3ERS = 672 SF kTERALS SUSPENDED FROM ERSIDE OF CHAMBERS. 5/32" , 3 -FEET O.C. 3HING VALVES AT THE END _ACH LATERAL. 58 min. 24' O PROPOSED OWTS 1' = 20•-1 TP 1 WATER SPIGOT BM 100' INSPECTION PORT AT BEGINNING AND END OF EACH TRENCH SAUNA OVERHE. UTILITY LINE N 2000 -GALLON TWO-COMPARTMETN POLY SEP1 W/ ORENCO PUMPING SYSTEM IN SECOND COI 4" DIAM SDR -35 SEWER PIPE WITH CLEANOUT (MIN 2% FALL TO TANK) 1 26' FUTURE 5 -BEDROOM 1,6 RESIDENCE 10) 26' 1 p { 73 COVERE DECK CHAMBER (4' x 3') 56' 14 CHAMBERS PER TRENCH P4 4' min. (recommend 6') 1.5" DIA SCH-40 SUSPENDED LATERALS WITH 5/32"--1 ORIFICES FACING UP 3' O.G. FIRST AND LAST ORIFICES FACE DOWN FOR DRAINAGE. ORIFICE SHIELDS INSTALLED UNDER DOWNWARD FACING ORIFICES. ®CHAMBER TRENCH � PLAN ROT r 4' max r LIMIT OF EXCAVATION i•IIUNDISTURBED SOL SUSPEND LATERALS WITH ZIP -TIES TO UNDERSIDE OF CHAMBERS 4' min 4" DIA SDR -35 INSPECTION PORT 2' min 0 CHAMBER TRENCH SECTION Not To \\_GRAVELLESS 'QUICK -4' CHAMBER (4' x 3') SCARIFY SURFACE LINE TO EACH TRENCH 1.5" DIA SCH-40 PUMP LINE FROM PUMP TANK ADV MODEL V6404A ACCESSIBLE AT GRADE PIPES PLACED IN TOP PORT OF CHAMBER END PLATES COMPACT SOIL BASE TO SUPPORT BOX USE HOLE SAW TO CUT THRU TOP OF END PLATE 0 AUTOMATIC DISTRI�BUTNG VALVE DE' NOT 30" DIAMETER PVC RISER (INSULATED) FROM EFFLUENT PUMPING SYSTEM El AUTO DISTF VALVI 1.5" DI PVC II OUTLI 0 AUTOMATIC DISTRIBUnl~ 10" DIA VALVE BOX WITH SECURED LID 1.5" PVC SLIP X MALE PIPE THREAD ADAPTOR W/CAP 1.5" DIA BALL VALVE 1.5" DIA SCH-40 PVC LONG SWEEP 90° ELBOW CHAMBER END CAP 1.5" DIA SCH-40 PVC SUSPENDED LATERAL 0 FLUSHING VALVE DETAIL E PERSONS/BEDROOM x 3 BEDROOMS + 150 GPD VIS) 600 GALLONS 00 -GALLONS )-COMPARTMENT CONCRETE SEPTIC TANK WITH TEM IN SECOND COMPARTMENT (STA): CE RATE (LTAR) = 0.5 GAL/ SQ FT TAR = 600 / 0.5 = 1200 SF INCHES = 1200 SF X 0.8 = 960 SF 1.7 = 672 SF / 12 SF / CHAMBER = 56 CHAMBERS AMBER TRENCHES IN EACH TRENCH ,MBERS 1- w w u_ d w 0 --0 — 2 — 3 — 4 — 5 — 6 — 7 — 8 —.9 — 10 UU NUI ULUt INSULATED COPPER TRACER WIRE 4" DIA SDR -35 SEWER LINE FINISHED GRADE TO TANK TO HOUSE CLEAN OUT DETAHer ILS SOIL PROFILE TEST PIT NO. 1 /• • / /• /• /• / /• .^ /• •r ✓• • / /• • / r• .✓ LIGHT BROWN, DENSE SANDY CLAY TAN, DENSE SANDY CLAY NO GROUNDWATER OR BEDROCK ENCOUNTERED DURING EXCAVATION SOILS LOG SOIL PROFILE TEST PIT NO. 3 —7 /• .• /• •/ ✓• / ./ /• /• •/ / /• f r• LIGHT BROWN, DENSE SANDY CLAY TAN, DENSE SANDY CLAY LEGEND Pq topsoil sandy clay NO" MIS PL/ AS 2000 Gallen Top Seam - 2CP Rein T-2cP-HH with High Head Pump DESIGN NOTES ■ Design per performance test per ASTM C1227 • Top surface area 87.75 ft2 • f'c ® 28 days; concrete = 6,000 PSI Min. Installation: • Tank to be set on 5" min. sand bed or pea gravel • Tank to be backfilled uniformly on all sides in lifts less than 24" and mechanically compacted ■ Excavated material may be used for backfill, provided large stones are removed • Excavation should be dewatered and tank filled with water prior to being put in service for installation with water table less than 2' below grade • Meets C1644-06 for resilient connectors • Inlet and Outlet identified above pipe • Delivered complete with internal piping ■ Control Panel to be mounted in sight line of tank • 4' Maximum bury depth ALLOWABLE BURY (Based on Water Table) WATER TABLE ALLOWABLE EARTH FILL 0'-0" 3'-0" 1' — 0" 3' — 0" 2' — 0" 4' — 0" 3'-0" 4'-0" DRY 4' — 0" 7 3" 162" TANK ID 20" Clear Access .. .. .r -� ...T 1) i I 24' Minimum Riser Height Quick boomed *Service contracts available for maintenance* Digging Specs Invert Dimensions 157"' ssttlon View Pump: • Lowers TS8 end improves effluent qua* to field • Complete installation (whim panel. mounting and start-up procedures) • Complete warranty Net Capacity Net Weight Min. 15' Long x 8' Wide Inlet Outlet Length Width Height Inlet Side Outlet Total Lid Tank 56" below inlet 56" 54"or73" 162" 78" 92" 1559 gal 507 gal 2066 gal Total 5420 lbs 15530 lbs 21150 lbs NrUVALLEY PRECAST, Inc. Buena Vista, Colorado Phone: 719-395-6764 Fax: 719-395-3727 webzfte: www.valleyprocast.00m Ema11: frontdesk@ivalleyprecastcom Orenco Biotube® ProPak Pump PackageTM 60 -Hz Series Pump Packages Float bracket External splice box Optional; internal splice box comes standard.) Control panel Riser lid (not included) Riser (not included) Discharge assembly Pump vault Float stem Floats Float collar Vault inlet holes 4 -in. (100 -mm) turbine effluent pump Biotube® filter cartridge Pump liquid end Pump motor Biotube® ProPakTM pump package components. General Orenco's Biotube® ProPak- is a complete, integrated pump package for filtering and pumping effluent from septic tanks. And its patented pump vault technology eliminates the need for separate dosing tanks. This document provides detailed information on the ProPak pump vault and filter, 4 -in. (100 -mm) 60 -Hz turbine effluent pump, and control panel. For more information on other ProPak components, see the following Orenco technical documents: • Float Switch Assemblies (NSU -MF -MF -1) • Discharge Assemblies (NTD -HV -HV -1) • Splice Boxes (NTD -SB -SB -1) • External Splice Box (NTD -SB -SB -1) Applications The Biotube ProPak is designed to filter and pump effluent to either gravity or pressurized discharge points. It is intended for use in a septic tank (one- or two-compartment) and can also be used in a pump tank. The Biotube ProPak is designed to allow the effluent filter to be removed for cleaning without the need to remove the pump vault or pump, simpli- fying servicing. Complete packages are available for on -demand or limed dosing sys- tems with flow rates of 20, 30, and 50-gpm (1.3, 1.9, and 3.2 Usec), as well as with 50 Hz and 60 Hz power supplies. Standard Models BPP20DD, BPP2ODD-SX, BPP3OTDA, BPP3OTDD-SX, BBPP5OTDA, BPP5OTDD-SX Product Code Diagram BPP C] C] - ❑ itandard options: Blank = 57 -in. (1448 -mm) vault height, intemal splice box, standard discharge assembly 68 = 68 -In (1727 -mm) vault height SX = external splice box CW = cold weather discharge assembly DB = drainback discharge assembly 0 = cam lock MFV = non -mercury float Control panel application: DD = demand -dosing TDA = timed -dosing, analog timer TDO = limed dosing, digital timer, elapsed lime meter & counters Pump flow rate, nominal: 20 = 20 gpnl(1.3 Usec) 30 = 30 gpm (1.9 Usec) 50 = 50 gpm (3.2 Usec) Biotube ProPak" pump vault Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD -BPP -1 Rev. 1.2, ® 08/14 Page 1 of 4 e -,111: I } I lb �y L� Pump liquid end Pump motor Biotube® ProPakTM pump package components. General Orenco's Biotube® ProPak- is a complete, integrated pump package for filtering and pumping effluent from septic tanks. And its patented pump vault technology eliminates the need for separate dosing tanks. This document provides detailed information on the ProPak pump vault and filter, 4 -in. (100 -mm) 60 -Hz turbine effluent pump, and control panel. For more information on other ProPak components, see the following Orenco technical documents: • Float Switch Assemblies (NSU -MF -MF -1) • Discharge Assemblies (NTD -HV -HV -1) • Splice Boxes (NTD -SB -SB -1) • External Splice Box (NTD -SB -SB -1) Applications The Biotube ProPak is designed to filter and pump effluent to either gravity or pressurized discharge points. It is intended for use in a septic tank (one- or two-compartment) and can also be used in a pump tank. The Biotube ProPak is designed to allow the effluent filter to be removed for cleaning without the need to remove the pump vault or pump, simpli- fying servicing. Complete packages are available for on -demand or limed dosing sys- tems with flow rates of 20, 30, and 50-gpm (1.3, 1.9, and 3.2 Usec), as well as with 50 Hz and 60 Hz power supplies. Standard Models BPP20DD, BPP2ODD-SX, BPP3OTDA, BPP3OTDD-SX, BBPP5OTDA, BPP5OTDD-SX Product Code Diagram BPP C] C] - ❑ itandard options: Blank = 57 -in. (1448 -mm) vault height, intemal splice box, standard discharge assembly 68 = 68 -In (1727 -mm) vault height SX = external splice box CW = cold weather discharge assembly DB = drainback discharge assembly 0 = cam lock MFV = non -mercury float Control panel application: DD = demand -dosing TDA = timed -dosing, analog timer TDO = limed dosing, digital timer, elapsed lime meter & counters Pump flow rate, nominal: 20 = 20 gpnl(1.3 Usec) 30 = 30 gpm (1.9 Usec) 50 = 50 gpm (3.2 Usec) Biotube ProPak" pump vault Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD -BPP -1 Rev. 1.2, ® 08/14 Page 1 of 4 Orenco ProPakTM Pump Vault Materials of Construction Vault body Polyethylene Support pipes Dimensions, in. (mmi A - Overall vault height B - Vault diameter PVC 57 (1448) or 68 (1727) 17.3 (439) C - Inlet hole height 19 (475) D - Inlet hole diameter (eight holes total) 2 (50) E - Vault top to support pipe bracket base 3 (76) F - Vault bottom to filter cartridge base 4 (102) A ■ E E v ,0 J zl ■ B ProPakTM pump vault (shown with Biotube filter and effluent pump) Biotube® Filter Cartridge Materials of Construction Filter tubes Polyethylene Cartridge end plates Polyurethane Handle assembly PVC Dimensions, in. (mm) A - Cartridge height 18 (457) B - Cartridge width 12 (305) Performance Biotube® mesh opening Total filter flow area 0.125 in. (3 mm)* 4.4 ft2 (0.4 m2) Total filter surface area 14.5 ft' (1.35 rn2) Maximum flow rate (I.6 -mm) filter mesh available A 140 gpm (8.8 Usec) g B 7 Biotube® filter cartridge (shown with float switch assembly) NTD -BPP -1 Rev. 1.2, ® 08114 Page 2 of 4 Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com Orenco® Technical Data Sheet 4-ln. (100 -mm) Turbine Effluent Pumps Orenco's 4 -in. (100 mm) Turbine Effluent Pumps are constructed of lightweight, corrosion -resistant stainless steel and engineered plastics; all are field -serviceable and repairable with common tools. All 60 -Hz PF Series models are CSA certified to the U.S. and Canadian safety standards for effluent pumps, and meet UL requirements. Power cords for Orenco's 4 -in. (100 -mm) turbine effluent pumps are Type SOOW 600-V motor cable (suitable for Class 1, Division 1 and 2 applications). Materials of Construction Discharge: Discharge bearing: Diffusers: Stainless steel or glass -filled polypropylene Engineered thermoplastic (PEEK) Glass filled PPO Impellers: Acetal (20-, 30-gmp), Noryl (50-gpm) Intake screens: Polypropylene Suction connection: Stainless steel Drive shaft: 300 series stainless steel Coupling: Sintered 300 series stainless steel Shell: 300 series stainless steel Lubricant: Deionized water and propylene glycol Specifications Nom. flow, Length Weight Discharge Impellers gpm (Usec) in. (mm) Ib (kg) in., nominal' 20 (1.3) 22.5 (572) 26 (11) 1.25 4 30 (1.9) 21.3 (541) 25 (11) 1.25 3 50 (3.2) 20.3 (516) 27 (12) 2.00 2 Performance Nom. flow, gpm (Usec) 20 (1.3) 30 (1.9) 50 (3.2) hp (IM Design flow amps 0.5 (0.37) 0.5 (0.37) 0.5 (0.37) 12.3 11.8 12.1 Rated Min liquid cycles/day level, in. (mm) 2 300 18 (457) 300 20 (508) 300 24 (610) ' Discharge is female NPT threaded, U.S, nominal size, to accommodate Orenco® discharge hose and valve assemblies. Consult your Orenco Distributor about fittings to connect discharge assemblies to metdc-sized piping, 2 Minimum liquid level is for single pumps when installed in an Orenco Biotube"• ProPakTM Pump Vault. Pump Curves Pump curves, such as those shown here, can help you determine the best pump for your system. Pump curves show the relationship between flow (gpm or Usec) and pressure (TDH), providing a graphical representation of a pump's performance range. Pumps perform best at their nominal flow rate, measured in gpm or L/sec. 140 m 120 • CZ 100 R ,oaeo so 40 1� 20 Flow in liters per second (I/sec) 0.63 1.26 1.89 2.52 3.15 339 4.42 PFRtl05111 PF 300511 FPF 508611 i 10 20 30 40 50 60 70 Flow in gallons per minute (gpml 43 37 30 ti 24 m a V 18 12 6 Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD -BPP -1 Rev. 1.Z ® 08/14 Page 3 of 4 Orenco® Control Panel (Demand Dose) Orenco's ProPak"' demand dose control panels are specifically engineered for the ProPak pump package and are ideal for applications such as demand dosing from a septic tank into a conventional gravity drainfield. Materials of Construction Enclosure UV -resistant fiberglass, UL Type 4X Hinges Stainless steel Dimensions, in. (mm) A - Height 11.5 (290) B - Width 9.5 (240) C - Depth 5.4 (135) Specifications Panel ratings 1. Motor -start contactor 120 V, 3/4 hp (0.56 kW), 14 A, single phase, 60 Hz 16 FLA, 1 hp (0,75 kW), 60 Hz; 2.5 million cycles at FLA (10 million at 50% of FLA) 2. Circuit 120 V, 10 A, OFF/ON switch, Single pole breakers 3. Toggle switch 4. Audio alarm Single -pole, double -throw HOA switch, 20 A 95 dB at 24 in. (600 mm), warble -tone sound, UL Type 4X 5. Audio alarm 120 V, automatic reset, DIN rail mount silence relay 6. Visual alarm 7/8 -in. (22 -mm) diameter red lens, "Push -to -silence," 120 V LED, UL Type 4X M.00 /. =0- k. 1. o Control panel, demand -dose Control Panel (Timed Dose) Orenco's ProPak timed dose control panels are specifically engineered for the ProPak pump package and are ideal for applications such as timed dosing from a septic tank into a pressurized drainfield or mound. Analog or digital timers are available. Materials of Construction Enclosure UV -resistant fiberglass, UL Type 4X Hinges Stainless steel Dimensions, in. (mm) A - Height 11.5 (290) B - Width 9.5 (240) C - Depth 5.4 (135) Specifications Panel ratings Dual -mode 120 V, 3/4 hp (0.56 kA, 14 A, single phase, 60 Hz Programmable for timed- or demand -dosing (digital timed -dosing panels only) 1a. Analog timer (not shown) 120 V, repeat cycle from 0.05 seconds to 30 hours, Separate variable controls for OFF and ON time periods 1 b. Digital timer (shown below) 120-V programmable logic unit with built-in LCD screen and programming keys. Provides control functions and timing for panel operation 2. Motor -start contactor 16 FLA, 1 hp (0.75 kW), 60 Hz; 2.5 million cycles at FLA (10 million at 50% of FLA) 3. Circuit breakers 120 V, 10 A, OFF/ON switch. Single pole 120 V 4. Toggle Switch 5. Audio alarm Single -pole, double -throw HOA switch, 20 A 95 dB at 24 in. (600 mm), warble -tone sound, UL Type 4X 6. Visual alarm 7/8 -in. (22 -mm) diameter red lens, "Push -to -silence", 120 V LED, UL Type 4X Control panel, timed -dose (digital timer model shown) NTD -BPP -1 Rev. 1.2, ® 08/14 Page 4 of 4 Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com Orenco PF Series 4 -inch (100 -mm) Submersible Effluent Pumps Applications Our 4 -inch (100 -mm) Submersible Effluent Pumps are designed to transport screened effluent (with low TSS counts) from septic tanks or separate dosing tanks. All our pumps are constructed of lightweight, corrosion -resistant stainless steel and engineered plastics; all are field - serviceable and repairable with common tools; and all 60 -Hz PF Series models are CSA certified to the U.S. and Canadian safety standards for effluent pumps, meeting UL requirements. Orenco's Effluent Pumps are used in a variety of applications, including pressurized drainfields, packed bed filters, mounds, aerobic units, effluent irrigation, effluent sewers, wetlands, lagoons, and more. These pumps are designed to be used with a Biotube® pump vault or after a secondary treatment system. Franklin Liquid End Franklin Super Stainless Motor C U5 LFIBt7980 LF12053898 --- Discharge Connection --- Bypass Orifice — Suction Connection Powered by Franklin Electric Features/Specifications To specify this pump for your installation, require the following: • Minimum 24-hour run -dry capability with no deterioration in pump life or performance* • Patented 1i8 -inch (3 -mm) bypass orifice to ensure flow recirculation for motor cooling and to prevent air bind • Liquid end repair kits available for better long-term cost of ownership • TRI-SEALTM floating impeller design on 10, 15, 20, and 30 gpm (0.6, 1.0, 1.3, and 1.9 Usec) models; floating stack design on 50 and 75 gpm (3.2 and 4.7 Usec) models • Franklin Electric Super Stainless motor, rated for continuous use and frequent cycling • Type SOOW 600-V motor cable • Five-year warranty on pump or retrofit liquid end from date of manu- facture against defects in materials or workmanship Not applicable for 5 -hp (3.73 A14) models Standard Models See specifications chart, pages 2-3, for a list of standard pumps. For a complete list of available pumps, call Orenco. Product Code Diagram PF [ lord length, ft (m):t Blank = 10 (3) 20 = 20 (6) 30 = 30 (9) 50 = 50 (15) Voltage, nameplate: 1 = 115" 200 = 200 2 = 2301 4 = 460 Frequency: 1 = single-phase 60 Hz 3 = three-phase 60 Hz 5 = single-phase 50 Hz Horsepower (kW): 03 = 1/3 hp (0.25) 07 = a/ hp (0.56) 15 — 1-1h hp (1.11) 30 = 3 hp (2.24) Nominal flow, gpm (Usec): 10 = 10 (0.6) 15 = 15 (1.0) 20 = 20 (1.3) 30 = 30 (1.9) 50 = 50 (3.2) 75 = 75 (4.7) 05 = h hp (0.37) 10 = 1 hp (0.75) 20 = 2 hp (1.50) 50 = 5 hp (3.73) Pump, PF Series ' 1/2 -hp (0.371A only 1220 volts for 50 Hz pumps Note: 20 -foot cords are available only for single-phase c nlr'. through 1-1 hp Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 •541-459-4449 • www.orenco.com NTD-PU-PF-1 Rev. 2.2, ® 09/14 Page 1 of 6 Specifications, 60 Hz N g d g I g 92 aai sw, Mosco .g E C2 2 L z 7 Q c, m CO Length, in. (mm) Rated cycles/day Pump Model PF100511 10 (0.6) 0.50 (0.37) 1 115 120 12,7 12.7 6 1 14 in. GFP 23.0 (660) 16 (406) 26 (12) 300 PF100512 10 (0.6) 0.50 (0.37) 1 230 240 6.3 6.3 6 1 1/4 in. GFP 23.0 (660) 16 (406) 26 (12) 300 PF10053200 10 (0.6) 0.50 (0.37) 3 200 208 3.8 3.8 6 1 '/4 in. GFP 23.0 (660) 16 (406) 26 (12) 300 PF100712 4.5 10 (0.6) 0.75 (0.56) 1 230 240 8.3 8.3 8 1 1/4 in. GFP 25.9 (658) 17 (432) 30 (14) 300 PF10073200 4.5 10 (0.6) 0.75 (0.56) 3 200 208 5.1 5.2 8 1 1/4 in. GFP 25.4 (645) 17 (432) 31 (14) 300 PF101012 5, 6 10 (0.6) 1.00 (0.75) 1 230 240 9.6 9.6 9 1 1/4 in. GFP 27.9 (709) 18 (457) 33 (15) 100 PF10103200 5 6 10 (0.6) 1.00 (0.75) 3 200 208 5.5 5.5 9 1 1/4 in. GFP 27.3 (693) 18 (457) 37 (17) 300 PF102012 6, 7 8 10 (0.6) 2.00 (1.49) 1 230 240 12.1 12.1 18 1 '/4 in. SS 39.5 (1003) 22 (559) 48 (22) 100 PF102032 5• & e 10 (0.6) 2.00 (149) 3 230 240 7.5 7.6 18 1 1/4 in. SS 37.9 (963) 20 (508) 44 (20) 300 PF10203200 6, 8 10 (0.6) 2.00 (1.49) 3 200 208 8.7 8.7 18 1 '/4 in. SS 37.9 (963) 20 (508) 44 (20) 300 PF150311 15 (1.0) 0.33 (0.25) 1 115 120 8.7 8.8 3 1 'f4 in. GFP 19.5 (495) 15 (380) 23 (10) 300 PF150312 15 (1.0) 0.33 (0.25) 1 230 240 4.4 4.5 3 1 1/4 in. GFP 19.5 (495) 15 (380) 23 (10) 300 PF200511 20 (1.3) 0,50 (0.37) 1 115 120 12.3 12.5 4 1 1/4 in. GFP 22.3 (566) 18 (457) 25 (11) 300 PF200512 20 (1.3) 0.50 (0.37) 1 230 240 6.4 6.5 4 1 11/4 in. GFP 22.5 (572) 18 (457) 26 (12) 300 PF20053200 20 (1.3) 0.50 (0.37) 3 200 208 3.7 3.8 4 1 11/4 in. GFP 22.3 (566) 18 (457) 26 (12) 300 PF201012 4.5 20 (1.3) 1.00 (0.75) 1 230 240 10.5 10.5 7 1 1/4 in. GFP 28.4 (721) 20 (508) 33 (15) 100 PF20103200 4.5 20 (1.3) 1.00 (0.75) 3 200 208 5.8 5.9 7 1 '/4 in. GFP 27.8 (706) 20 (508) 33 (15) 300 PF201512 4.5 20 (1.3) 1.50 (1.11) 1 230 240 12.4 12.6 9 1 1/4 in. GFP 34.0 (864) 24 (610) 41 (19) 100 PF20153200 4,5 20 (1.3) 1.50 (1.11) 3 200 208 7.1 7.2 9 1 '/ in. GFP 30.7 (780) 20 (508) 35 (16) 300 PF300511 30 (1.9) 0.50 (0.37) 1 115 120 11.8 11.8 3 1 11/4 in. GFP 21.3 (541) 20 (508) 28 (13) 300 PF300512 30 (1.9) 0.50 (0.37) 1 230 240 6.2 6.2 3 1 1/4 in. GFP 21.3 (541) 20 (508) 25 (11) 300 PF30053200 30 (1.9) 0.50 (0.37) 3 200 208 3.6 3.6 3 1 1/4 in. GFP 21.3 (541) 20 (508) 25 (11) 300 PF300712 30 (1.9) 0.75 (0.56) 1 230 240 8.5 8.5 5 1 1/4 in. GFP 24,8 (630) 21 (533) 29 (13) 300 PF30073200 30 (1.9) 0.75 (0.56) 3 200 208 4.9 4.9 5 1 11/4 in. GFP 24.6 (625) 21 (533) 30 (14) 300 PF301012 4 30 (1.9) 1.00 (0.75) 1 230 240 10.4 10.4 6 1 '/4 in. GFP 27.0 (686) 22 (559) 32 (15) 100 PF30103200 4 30 (1.9) 1.00 (0.75) 3 200 208 5.8 5.8 6 1 1/4 in. GFP 26.4 (671) 22 (559) 33 (15) 300 PF301512 4 5 30 (1.9) 1.50 (1.11) 1 230 240 12.6 12.6 8 1 '/4 in. GFP 32.8 (833) 24 (610) 40 (18) 100 PF30153200 4.5 30 (1.9) 1.50 (1.11) 3 200 208 6.9 6.9 8 1 1/4 in. GFP 29.8 (757) 22 (559) 34 (15) 300 PF301534 4.5 30 (1.9) 1.50 (1.11) 3 460 480 2.8 2.8 8 1 Y in. GFP 29.5 (685) 22 (559) 34 (15) 300 PF302012 5' 6' 30 (1.9) 2.00 (1.49) 1 230 240 11.0 11.0 10 1 '/4 in. SS 35,5 (902) 26 (660) 44 (20) 100 PF30203200 5.6 30 (1.9) 2.00 (1.49) 3 200 208 9.3 9.3 10 1 '/4 in. SS 34.0 (864) 24 (610) 41 (19) 300 PF303012 5.6.7.8 30 (1.9) 3.00 (2.23) 1 230 2.40 16.8 16.8 14 1 1/4 in. SS 44.5 (1130) 33 (838) 54 (24) 100 PF303032 5' 6' 8 30 (1.9) 3.00 (2.23) 3 230 240 10.0 10.1 14 1 1/4 in. SS 44.3 (1125) 27 (686) 52 (24) 300 PF305012 5,6 7 8 30 (1.9) 5.00 (3.73) 1 230 240 25,6 25.8 23 1 Y in. SS 66.5 (1689) 53 (1346) 82 (37) 100 PF305032 5.68 30 (1.9) 5.00 (3.73) 3 230 240 16.6 16.6 23 1 '/4 in. SS 60.8 (1544) 48 (1219) 66 (30) 300 PF30503200 5, 6• e 30 (1.9) 5.00 (3.73) 3 200 208 18.7 18.7 23 1 1/4 in. SS 60.8 (1544) 48 (1219) 66 (30) 300 PF500511 50 (3.2) 0.50 (0.37) 1 115 120 12.1 12.1 2 2 in. SS 20.3 (516) 24 (6.10) 27 (12) 300 PF500512 50 (3.2) 0.50 (0.37) 1 230 240 6.2 6.2 2 2 in. SS 20.3 (516) 24 (610) 27 (12) 300 PF500532 50 (3.2) 0.50 (0.37) 3 230 240 3.0 3.0 2 2 in. SS 20.3 (516) 24 (610) 28 (13) 300 PF50053200 50 (3.2) 0.50 (0.37) 3 200 208 3.7 3.7 2 2 in. SS 20.3 (516) 24 (610) 28 (13) 300 PF500534 50 (3.2) 0.50 (0.37) 3 460 480 -1.5 1.5 2 2 in. SS 20.3 (516) 24 (610) 28 (13) 300 PF500712 50 (3.2) 0.75 (0.56) 1 230 240 8.5 8.5 3 2 in. SS 23.7 (602) 25 (635) 31 (14) 300 PF500732 50 (3.2) 0.75 (0,56) 3 230 240 3.9 3.9 3 2 in. SS 23.7 (602) 25 (635) 32 (15) 300 PF50073200 50 (3.2) 0.75 (0.56) 3 200 208 4.9 4.9 3 2 in. SS 23.1 (587) 26 (660) 32 (15) 300 NTD-PU-PF-1 Rev. 2.2, 0 09/14 Page 2 of 6 Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com Technical Data Sheet Orenco® Specifications, 60 Hz (continued) cZ s- Pump Model Q o g E 0 E Length, in, (mm) Y 715 Rated cycles/day PF500134 PF501012 PF50103200 PF501034 PF5015124 PF501532004 PF503012 a. c.'. 6 PF50303200' 9 PF503034 4 5.8 PF505012 5.8 7,8 PF505032 5,8'7.8 PF751012 PF751512 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 75 (4.7) 75 (4.7) 0.75 (0.56) 1.00 (0.75) 1.00 (0.75) 1.00 (0.75) 1.50 (1.11) 1.50 (1.11) 3.00 (2.23) 3.00 (2.23) 3.00 (2.23) 5.00 (3.73) 5.00 (3.73) 1.00 (0.75) 1.50 (1.11) 3 460 1 230 3 200 3 460 1 230 3 200 1 230 3 200 3 460 1 230 3 230 1 230 1 230 480 240 208 480 240 208 240 208 480 240 240 240 240 1.8 10.1 5.7 2.2 12.5 7.0 17.7 13.1 5-3 26.2 16,5 9.9 12.1 i8 10.1 5.7 2.2 12.6 7.0 17.7 13.1 5.3 26.4 16.5 10.0 12.3 3 4 4 4 5 5 8 8 8 13 13 3 4 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 2 in. SS 34.8 (884) 27.0 (686) 26.4 (671) 26.4 (671) 32.5 (826) 29.3 (744) 43.0 (1092) 43.4 (1102) 40.0 (1016) 65.4 (1661) 59.3 (1506) 27.0 (686) 33.4 (848) 25 (635) 26 (660) 26 (660) 26 (660) 30 (762) 26 (660) 37 (940) 30 (762) 31 (787) 55 (1397) 49 (1245) 27 (686) 30 (762) 31 (14) 35 (16) 39 (18) 39 (18) 41 (19) 35 (16) 55 (25) 55 (25) 55 (25) 64 (29) 64 (29) 34 (15) 44 (20) 300 100 300 300 100 300 100 300 300 300 300 100 100 Specifications, 50 Hz Pump Model PF100552 PF100752 a, s PF101552 6 PF300552 PF300752 PF301052 PF301552 '' 5 PF500552 PF500752 PF501052 PF501552 PF751052 10 (0.6) 10 (0.6) 10 (0.6) 30 (1.9) 30 (1.9) 30 (1.9) 30 (1.9) 50 (3.2) 50 (3.2) 50 (3.2) 50 (3.2) 75 (3.2) 0.50 (0.37) 0.75 (0.56) 1.50 (1.11) 0.50 (0.37) 0.75 (0.56) 1.00 (0.75) 1.50 (1.11) 0.50 (0.37) 0.75 (0.56) 1.00 (0.75) 1.50 (1.11) 1.00 (0.75) 220 220 220 220 220 220 220 220 220 220 220 220 230 230 230 230 230 230 230 230 230 230 230 230 3.9 6.2 10.5 4.1 6.1 7.4 9.3 4.0 6.3 7.3 9.1 7.3 4.1 6.2 11.4 4.1 6.1 7.4 9.3 4.0 6.4 7.4 9.1 7.3 6 1Yin, GFP 9 1 1/ in. GFP 18 1 Yn in. SS 4 1 Ya in. GFP 5 1 % in. GFP 7 11/Qin. GFP 8 1 1/a in. GFP 2 2 in. SS 3 2 in. SS 4 2 in. SS 5 2 in. SS 4 2in.SS 23,0 (584) 26.8 (658) 39.5 (1003) 22.5 (572) 24.8 (630) 28.4 (721) 35.4 (899) 20.3 (516) 23.7 (602) 27.0 (686) 32.5 (826) 30.0 (762) 17 (432) 17 (432) 22 (559) 19 (483) 19 (483) 20 (508) 24 (610) 25 (635) 25 (635) 26 (660) 30 (762) 27 (686) 26 (12) 30 (14) 46 (21) 26 (12) 29 (13) 32 (15) 40 (18) 29 (13) 31 (14) 35 (16) 42 (19) 34 (15) 300 300 300 300 300 100 100 300 300 100 100 100 1 GFP = glass -filled polypropylene; SS stainless steel. The 1 ',-in. NPT GFP discharge is 2 7,8 in. octagonal across flats; the 1 kin. NPT 2 irr. NPT SS dischauge is 2 778 ln, hexagonal across flats. Discharge is female NPT threaded, U.S, nominal size, to accommodate Orenco" Distributor about fittings to connect hose and valve assenrbiies to metric -sized piping, 2 Minimum liquid level is for single pumps when installed in an Orenco Biotubd `' Pump Vault or Universal Flow Inducer in other applications, Orenco for more information. 3 Weight includes carton and 10 -ft (3 -in) cord. 4 High-pressure discharge assembly required.. 5 Do nol use carp -lock option (0) on discharge assembly. 6 Custom discharge assembly required for these pumps. Contact Orenco. 7 Capacitor pack (sold separately or installed in a custom control panel) required for this pump. Contact Orenco. 6 Torque locks are available for all pumps, and are supplied with 3 -hp and 5 -hp pumps. SS discharge is 2 V8 in. octagonal across flats; and the discharge hose and valve assemblies. Consult your Orenco minimum liquid revel should be top of pump. Consult Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD-PU-PF-1 Rev. 2.2, © 09/14 Page 3 of 6 Orenco® Materials of Construction Discharge Glass -filled polypropylene or stainless steel Discharge bearing Engineered thermoplastic (PEEK) Diffusers Glass -filled PPO (Noryl GFN3) Impellers Celcon® acetal copolymer on 10-, 20, and 30-gpm models; 50-gpm impellers are Noryl GFN3 Intake screen Polypropylene Suction connection Stainless steel Drive shaft 7/16 inch hexagonal stainless steel, 300 series Coupling Sintered stainless steel, 300 series Shell Stainless steel, 300 series Motor Franklin motor exterior constructed of stainless steel. Motor filled with deionized water and propylene glycol for constant lubrication. Hermetically sealed motor housing ensures moisture -free windings. All thrust absorbed by Kingsbury -type thrust bearing. Rated for continuous duty. Single- phase motors and 200 and 230 V 3-phase motors equipped with surge arrestors for added security. Single-phase motors through 1,5 hp (1.11 kW) have built-in thermal overload protection, which trips at 203-221° F (95-105° C), Using a Pump Curve A pump curve helps you determine the best pump for your system. Pump curves show the relationship between flow (gpm or Usec) and pressure (total dynamic head, or TDH), providing a graphical representation of a pump's optimal performance range. Pumps perform best at their nominal flow rate — the value, measured in gpm, expressed by the first two numerals in an Orenco pump nomenclature. The graphs in this section show optimal pump operation ranges with a solid line. Flow flow rates outside of these ranges are shown with a dashed line. For the most accurate pump specification, use Orenco's PumpSelect- software. Pump Curves, 60 Hz Models 800 700 as a) • 500 ▪ en• 400 • 09 300 200 600 100 lY 1 1 1 j 1 1 1 • = •.. — - •LPF10 Series, 60 Hz, 0.5 - 2.0 hp EPF1020 .. 1 PF 1010 �] 11$F1005 _— — PF1005•FC �; —'— w/'/4"flow " N. — — — controller 160 140 as 120 ne 0 100 r 80 60 40 ti 20 PF15 Series, 60 Hz, 0.3 hp IPF15O3f 2 4 6 8 10 12 14 16 0 3 6 9 12 15 18 21 24 Flow in gallons per minute (gpm) Flow in gallons per minute (gpm) NTD-PU-PF-1 Rev. 2.2, C) 09/14 Page 4 of 6 Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843. 541-459-4449 • www.orenco.com N O Ca 01 01 0 Total dynamic head (TDH) in feet N N W C�.] •=, C71 O 01 O CJ1 0 0 0 0 0 0 0 0 0 w 0 01 OD O V O O O (0 0 0 0 Total dynamic head (TDH) in feet CD W 0 OD 01 CD O 0 , 1 -F J N- .; y r� L 1 1 E t`• 1 1-7— r • } f! . 17. 1 9 .• i 1 1 'F50 Series, 60 Hz, 1 i- { .,1 , jf/1 N 1 f[ 1 i 1 1 1 PF75 Series, 60 Hz, 1.1 I O N CD I ` i i111/1/1 ...- 1/ cri1 r1 I O WI gmb 1l ! / i 0 0 w 0 01 OD O V O O O (0 0 0 0 Total dynamic head (TDH) in feet CD W 0 OD 01 CD O 0 , 1 -F J N- .; y r� L 1 1 E t`• 1 1-7— 17. 1 .• 1 1 y is .,1 , N 1 f[ 1 i 1 1 1 PF75 Series, 60 Hz, 1.1 O N CD ` ., ...- 1/ r1 I O WI 1l ! / i 1 1 cn 1 17 G I I,o 1 it 11 f i co a= Flow in gallons per minute (gpm) 01 0 01 0 w CD w 0 Total dynamic head (TDH) in feet O CT O [TI - O U1 ▪ O CTI • O 2 O =■ a 0 01 0 N 01 w 0 (4 01 0 Total dynamic head (TDH) in feet - N W . CTI CO O O 0 0 O O Ogi O O 0 CO O O I -11 WCL 0 0. CD 1.7 y 0 0. 0 0 O, '0: J .; y r� N O N CD ` O WI cn 17 a 0 01 0 N 01 w 0 (4 01 0 Total dynamic head (TDH) in feet - N W . CTI CO O O 0 0 O O Ogi O O 0 CO O O I -11 WCL 0 0. CD 1.7 y 0 0. 0 0 O, Orenco eirnic . - lJaia Sheet Pump Curves, 50 Hz Models 180 160 . 140 m 120 C 100 aa) •• 80 • 60 a c 40 20 0 Flow in gallons per minute (gpm), nominal 1.6 32 4.8 63 7.9 9.5 11 13 1 r f 1 PF10 Series, 50 Hz, 0.37 -1.11 kW, PF101552 PF1991152 PF100552 �_ J'— — PF1005-FC ay/ 6mmflow controller r.4%. I i 0.1 02 03 0.4 05 06 0,7 08 Flow in liters per second (Usec) Flow n gallons per minute (gpm), nominal 7 9 16 24 32 40 48 56 63 F 1 I PF50 Series, 50 Hz, 0.31-1.11 kWj 120 525 m e 100 459 e y m •.: E 394 a .P. 80 c Z 328 x 0 C to 60 262 m - ea eaE 197 '� > 40 C 'D 131 :9 v � "- 20 66 152 09 131 w .- 115 115 98 a 82 66 eee 49 'E 33 le . 16 19 0.5 1.0 1.5 2.0 2.5 3.0 3.5 40 45 Flow in liters per second (Usec) Flow in gallons per minute (gpm), nominal 63 13 19 25 32 00 30 27 24 21 Mi 18 m 15 •= 12 ? 6 PF30 Series, 50 Hz, 0.37 -1.11 kW 328 0 262 ,A7 O 197 131 E m s, 66 04 0.8 12 16 20 2.4 Flow in liters per second (Usec) Flow in gallons per minute (gpm), nominal 10 19 29 38 48 57 67 76 86 1 PF75 Series, 50 Hz, 0.75 kW 06 12 1.8 2.4 3.0 3.6 42 48 5.4 6.0 Flow in liters per second (L/sec) 89 m 79 69 w 59 49 39 .e 30 ruE a., 20 ; w NTD-PU-PF-1 Rev. 2.2, © 09/14 Page 6 of 6 Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com This article may describe design criteria that was in effect at the time the article was written. FOR CURRENT DESIGN CRITERIA, call Orenco Systems, Inc. at 1-800-348-9843. Orenco Automatic Distributing Valve Assemblies For Wastewater Effluent Systems Introduction Orenco's automatic distributing valve assemblies, pressurized with small high -head effluent pumps, are useful for distributing effluent to multiple zones. These zones can be segments of sand filter manifolds, drainfields, or other effluent distribution systems. Distributing valve assemblies can substantially simplify the design and installation of a distribution sys- tem and reduce installation costs. This is particularly true where a distributing valve assem- bly is used instead of multiple pumps and/or electrically operated valves. Additionally, a reduction in long term operation and maintenance costs is realized due to a reduced size and/or number of pumps. More even distribution can be achieved on sloping sites by zoning laterals at equal elevations. This eliminates drainback to lower lines and the unequal distrib- ution of effluent that occurs at the beginning of a cycle. Valve Operation The valve itself has only a few moving parts, requires no electricity, and alternates automati- cally each cycle. Refer to Figure 1 for the following valve operation description. The flow of the incoming effluent forces the rubber flap disk 0 to seat against the valve bottom 0. The opening 0 in the rubber flap disk aligns with an opening in the valve bottom to allow flow to only one valve outlet. The stem 0 houses a stainless steel spring which pushes the rubber flap disk away from the valve bottom after the flow of effluent stops. The stem acts as a cam follower and rotates the rubber flap disk as the stem is raised and lowered through the cam 0. The force from the flow of effluent pushes the stem down through the cam and the stainless steel spring pushes the stem back up through the cam when the flow of effluent stops. Each linear motion of the stem allows the rubber flap disk to rotate half the distance necessary to reach the next outlet. When there is no flow, the rubber flap disk is in the "up" position and is not seated against the valve bottom. 0 0 0 Outlets Figure 1: 6000 Series Value Orenco Systems" incorporated 1^800`348-9843 NTP -VA -1 Rev. 1.2, ©11/03 ,; Orenco Systems®, Inc. Page 1 o16 Figure 2: Orenco Distributing Valve Assembly (6000 Series Valve) The Distributing Valve Assembly The Orenco Automatic Distributing Valve Assembly combines the distributing valve itself and sever- al other components to give a complete preassembled unit that is easy to install, monitor, and main- tain. Figure 2 shows a complete assembly. Because distributing valves with several outlets can be difficult to line up and glue together in the field, the discharge lines in the assemblies are glued in place at Orenco. The unions (1) allow removal and maintenance of the valve. The clear PVC pipe sections (2) give a visual check of which discharge line is being pressurized. The inlet ball valve (3) allows a quick, simple method to test for proper valve cycling. The ball valve also stops the flow of effluent in case the pump is activated unexpectedly during maintenance or inspection. Check valves may be necessary on the discharge lines. Use of check valves is discussed in the valve positioning section. Valve Assembly Hydraulics Liquid flowing through the valve assembly must pass through fairly small openings and make several changes in direction. Because of this, headlosses through the valve assembly are fairly high. Table 1 gives the headloss equations for several different assemblies and Figure 3 shows the graphical repre- sentations of these equations. Orenco recommends that high -head turbine pumps be used to pressur- ize the valve assemblies to ensure enough head is available for proper system operation. High -head turbine pumps are also recommended because the use of a distributing valve usually requires more frequent pump cycling. The high -head turbine pumps are designed for high cycling systems and will outlast conventional effluent pumps by a factor of 10 or more in a high cycling mode. Furthermore, the high -head turbine pump intake is 12 inches or more above the bottom of the pump and tends to prevent any settled solids from being pumped into the distribution valve and obstructing its opera- tion. A minimum flow rate through the distributing valve is required to ensure proper seating of the rubber flap disk. Minimum flow rates for the various models are given in Table 1. NTP -VA -1 Rev. 1.2, © 11/03 Orenco Systems®, Inc. Page 2of6 Table 1. Automatic Distributing Valve Assembly Headloss Equations Model Series Equation Operating Range (gpm) V4400A HL = 0.085 x Q1•45 V4600A HL = 0.085 x Q1•58 V6400A HL = 0.0045 x Q2 + 3.5 x (1 - e-0 06Q) V6600A HL = 0.0049 x Q2 + 5.5 x (1 - e 0.1 Q) Head Loss Through Assembly (ft.) 35 30 25 20 15 10 5 0 10-40 10-25 15-70 15-70 10 15 20 25 30 35 40 45 50 55 60 65 70 Flow (gpm) Figure 3: Automatic distributing valve assembly headless curves The Pumping System Although the distributing valve was designed for the irrigation industry, it has started to gain fairly wide acceptance in the effluent pumping industry. However, because of the mechanical movements of the valve, it is necessary to take steps to prevent solids from reaching the distributing valve that may impede the operation of the valve. Orenco BiotubeF Pump Vaults when properly sized and installed — provide the necessary protection to prevent valve malfunction. The Biotube pump vault accepts effluent only from the clear zone between a tank's scum and sludge layers and then filters this effluent through a very large surface area screen cartridge. Without this protection in effluent systems, the valve has very little chance of reliable long-term operation. NTP -VA -1 Rev. 1.2, ©11/03 Orenco Systems®, Inc. Page 3 of 6 Valve Positioning The physical position of the valve in relation to the pump and the discharge point is very important for proper valve operation. The most reliable operation occurs when the valve is placed at the high point in the system and as close to the pump as possible. The transport line between the pump and valve should be kept full if possible. If the line is empty at the beginning of each cycle, pockets of air during filling can cause random rotation of the valve. The valve is particularly vulnerable to this erratic rotation with empty lines that are long and not laid at a constant grade. An ideal valve loca- tion is shown in Figure 4. If the final discharge point is more than about 2 feet above the valve and the system does not drain back into the dosing tank, check valves should be installed on the lines immediately following the valve and a pressure release hole or line should be installed just prior to the valve. This pressure release hole or line can go into a return line to the dosing tank or to a "minidrainfield" near the valve. In order for the valve to rotate reliably, no more than about 2 feet of head should remain against the valve to allow the rubber flap disk to return to its up position. In many cases, it may take from one minute to several minutes for the pressure in the valve to be lowered enough for proper rotation to occur. Special care should be taken when installing systems controlled by programmable timers to ensure cycling does not occur too rapidly. Figure 5 illustrates a valve assembly using check valves. Pumping downhill to the valve should be avoided unless the transport line is very short and the ele- vation between the discharge line out of the tank and the valve is less than about 2 feet. If the valve is located many feet below the dosing tank, random cycling may occur while the transport line drains through the valve at the end of the cycle. A pressure sustaining valve located just before the distrib- uting valve may overcome this problem in some instances. —4— Dosing Tank Transport Line Distributing Valve Assembly Discharge Laterals Figure 4: Ideal valve location NTP -VA -1 Ray. 1.2, ©11/03 Orenco Systems®, Inc. Page4of6 System Startup Refer to the Hydrotek Valve booklet that is provided with the distributing valve assembly for the sequencing of the valve outlets. The transport line should always be flushed with clean water before installing the valve. Any sand, gravel, or other foreign objects that may have been in the pipe during installation can easily become lodged in the distributing valve, causing malfunction. With the pump running, alternately close and open the ball valve on the distributing valve assembly to check proper rotation of the valve. (Note: If check valves are used on the lines after the distribut- ing valve, the pump may need to be turned on and off to allow the pressure to be released from the valve.) If visual operation of which zone is operating is not possible, watch the clear pipe on each line for indication of which zone is operating. Pressure Release Line if h>2'-0" Dosing Tank Transport Line Figure 5: Valve assembly below final discharge point Discharge Laterals ave Check Valves if h>2-0' ❑ialributing Valve Assernbly Maintenance Annually check for proper operation by following procedures listed in the Hydrotek Valve booklet and system startup procedures listed above. Troubleshooting 1. PROBLEM: Valve does not change or cycle to next zone or outlet CAUSE: The stem and disk assembly is not rotating when water flow is turned off and then back on. SOLUTION 1: Ensure that there is no debris inside the cam. Clean and carefully reinstall the cam. SOLUTION 2: If fewer than the maximum number of outlets are being used, check the installation of the cam. Ensure that the stem and disk assembly is not being held down by an improperly installed cam. Refer to the cam replacement instructions. NTP -VA -1 Rev. 1.2, ©11/03 Orenco Systems®, Inc. Page 5 o16 SOLUTION 3: SOLUTION 4: SOLUTION 5: SOLUTION 6: 2. PROBLEM: CAUSE: SOLUTION 1: SOLUTION 2: SOLUTION 3: 3. PROBLEM: CAUSE: Remove the valve top and check for proper movement of stem and disk assembly. Check for and remove any debris or foreign objects that may jam or retard the movement of the disk. Check for freedom of movement of stem and disk assembly up and down over the center pin in bottom of valve. Scale deposits may build up on the pin and hold stem and disk assembly down. Clean pin and again check for freedom of movement. Be sure that all operating outlets are not capped and that the flow to operating zones is not restricted in any manner. This would cause pressure to build up in the valve and lock the stem and disk assembly in the down position. The backflow of water from uphill lines may be preventing the valve from cycling properly. This can happen when the valve is placed too far below an elevated line. If the valve cannot be placed close to the high point of the system, a check valve should be installed near the valve in the outlet line that runs uphill from the valve and a drain line installed just prior to the valve to relieve the pressure. Water comes out of all the valve outlets Stem and disk assembly not seating properly on valve outlet. Check for sufficient water flow. A minimum flow rate is required to properly seat the disk as shown in Table 1. Remove the valve top and check the inside walls to ensure that nothing is interfering with the up and down movement of the stem and disk assembly inside the valve. Make sure that the operating outlets are not capped and that the flow to the operat- ing zones are not restricted in any manner. Valve skips outlets or zones Pumping into an empty transport line — especially downhill — may cause the valve to skip outlets from pockets of air allowing the rubber flap disk to raise during a cycle. SOLUTION 1: Keep the transport line full. SOLUTION 2: If the line must remain empty between cycles, use a larger diameter transport line laid at a constant grade to prevent air pockets from forming. CAUSE: SOLUTION 1: The stem and disk assembly is being advanced past the desired outlet. Ensure that the correct cam for the desired number of zones is installed and that the outlet lines are installed to the correct outlet ports of the valve as indicated by the zone numbers on the top of the cam. NTP -VA -1 Rev. 12. ©11/03 Orenco Systems®, Inc. Page 6 of 6 Distributing Valves Submittal Data Sheet Applications Automatic Distributing Valve Assemblies are used to pressurize multiple zone distribution systems including textile filters, sand filters and drainfields. distributing valve elbow Bottom View Specifications Side View General o Orenco Systems° Incorporated 1-800-348-9843 Orenco's Automatic Distributing Valve Assemblies are mechanically operated and sequentially redirect the pump's flow to multiple zones or cells in a distribution field. Valve actuation is accomplished by a combination of pressure and flow. Automatic Distributing Valve Assemblies allow the use of smaller horsepower pumps on large sand filters and drainfields. For example, a large community drainfield requiring 300 gpm can use a six -line Valve Assembly to reduce the pump flow rate requirement to only 50 gpm. Orenco only warrants Automatic Distributing Valves when used in conjunction with High -Head Effluent Pumps with Biotube Pump Vaults to provide pressure and flow requirements, and to prevent debris from fouling valve operation. An inlet ball valve and a section of clear pipe and union for each outlet are provided for a complete assembly that is easy to maintain and monitor. Ideal valve location is at the high point in the system. Refer to Automatic Distributing Valve Assemblies (NTP -VA -1) for more information. Standard Models V4402A, V4403A, V4404A, V4605A, V4606A, V6402A, V6403A, V6404A, V6605A, V6606A. Nomenclature VDDDDA Indicates assembly Number of active outlets Model series: 44 = 4400 series (2-4 outlets) 46 = 4600 series (5-6 outlets) 64 = 6400 series (2-4 outlets) 66 = 6600 series (5-6 outlets) Distributing valve Materials of Construction All Fittings: Unions: Ball Valve: Clear Pipe: V4XXX Distributing Valves: V6XXX Distributing Valves: Sch. 40 PVC per ASTM specification Sch. 80 PVC per ASTM specification Sch. 40 PVC per ASTM specification Sch. 40 PVC per ASTM specification High-strength noncorrosive ABS polymer and stainless steel High-strength noncorrosive ABS polymer, stainless steel, and die cast metal NSU -SF -VA -1 Rev. 3.0, © 4/03 Page 1 of 2 Distributing Valves (continued) Head Loss Through Assembly (ft.) 35 30 25 20 15 10 5 0 V4600A V4400A V6600A V6400A 1 1 1 1 —11 1 1 1 1 1 1 i i i i 1, 0 5 10 15 20 25 30 35 40 45 50 55 60 65 70 Flow (gpm) Model Inlet Size (in.) Outlets Size (in.) Flow range (gpm) Max Head (ft.) Min. Enclosure V4402A 1.25 1.25 10 - 40 170 VB1217 V4403A 1,25 1.25 10 - 40 170 VB1217 V4404A 1.25 1.25 10 - 40 170 VB1217 V4605A 1.25 1.25 10 - 25 170 RR2418 V4606A 1.25 1.25 10 - 25 170 RR2418 V6402A 1.5 1.5 15 -100 345 RR2418 V6403A 1.5 1.5 15 -100 345 RR2418 V6404A 1.5 1.5 15 -100 345 RR2418 V6605A 1.5 1.5 15 -100 345 RR2418 V6606A 1.5 1,5 15 -100 345 RR2418 NSU -SF -VA -I Rev. 3.0, © 9/03 Page 2 of 2 INFILTRATOR` water technologies -Quick4 The Quick4® Plus Standard Chamber Quick4 PIusTM Series -The-Quick4 Plus Standard Chamber offers maximum strength through its two center structural columns. This chamber can be installed in a 36 -inch -wide trench. Like the original line of Quick4 chambers, it offers advanced contouring capability with its Contour Swivel ConnectionTM which permits turns up to 15 -degrees, right or left. It is also available in four -foot lengths to provide optimal installation flexibility. The Quick4 Plus All -in -One 12 Endcap, and the Quick4 Periscope are available with this chamber, providing increased flexibility in system configurations. ANIL Maximum Strength Quick4 Plus Standard Chamber Specifications Size 34"W x 53"L x 12"H (864 mm x 1346 mm x 305 mm) Effective Length 48" (1219 mm) Louver Height 8" (203 mm) Storage Capacity 47 gal (178 L) Invert Height 0.6" (15 mm), 5.3" (135 mm), 8.0" (203 mm), 12.7" (323 mm) Quick4 Plus Standard Chamber Benefits: • Two center structural columns offer increased stability and superior strength • Advanced contouring connections • Latching mechanism allows for quick installation • Four -foot chamber lengths are easy to handle and install • Supports wheel loads of 16,000 lbs/axle with 12" of cover Quick4 Plus All -in -One 12 Endcap Benefits: • May be used at the end of chamber row for an inlet/outlet or can be installed mid -trench • Mid -trench connection feature allows construction of chamber rows with center feed, as an alternative to inletting at the ends of chamber rows • Center -feed connection allows for easy installation of serial distribution systems • Pipe connection options include sides, ends or top APPROVED in Quick4 Plus All -in -One Periscope Benefits: • Allows for raised invert installations • 180° directional inletting • 12" raised invert is ideal for serial applications Certified by the International Association of Plumbing and Mechanical Officials (IAPMO) ra) Quick4 Plus"' Series Quick4 Plus Standard Chamber Qffick4. 34° Quick4 Plus All -in -One 12 Endcap 48" EFFECTIVE LENGTH PRESSURIZED PIPE DRILL POINTS LOCATIONS (2 PLACES) jalfit% 33. FRONT VIEW Quick4 Plus All -in -One Periscope - 13' QUICK4 PLUS ALL -IN -ONE PERISCOPE (360° SWIVEL) Ir1C11 TDAT(%D water tecnnologies Italir INVERT 4 Business Park Road P.O. Box 768 Old Saybrook, CT 06475 860-577-7000 • Fax 860-577-7001 1-800-221-4436 www.infiltratorwater.com SIDE VIEW INFILTRATOR WATER TECHNOLOGIES STANDARD LIMITED WARRANTY (a) The structural integrity of each chamber, endcap and other accessory manufactured by Infiltrator ("Units"), when installed and operated in a leachfield of an onsite septic system in accordance with Infiltrators instructions, is warranted to the original purchaser ("Holder") against defective materials and workmanship for one year from the date that the septic permit is issued for the septic system containing the Units; provided, however, that if a septic permit is not required by applicable law, the warranty period will begin upon the date that installation of the septic system commences. To exercise its warranty rights, Holder must notify Infiltrator in writing at its Corporate Headquarters in Old Saybrook, Connecticut within fifteen (15) days of the alleged defect. Infiltrator will supply replacement Units for Units determined by Infiltrator to be covered by this Limited Warranty. Infiltrator's liability specifically excludes the cost of removal and/or installation of the Units. (b) THE LIMITED WARRANTY AND REMEDIES IN SUBPARAGRAPH (a) ARE EXCLUSIVE. THERE ARE NO OTHER WARRANTIES WITH RESPECT TO THE UNITS, INCLUDING NO IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE (c) This Limited Warranty shall be void if any part of the chamber system is manufactured by anyone other than Infiltrator. The Limited Warranty does not extend to incidental, consequential, special or indirect damages. Infiltrator shall not be liable for penalties or liquidated damages, including loss of production and profits, labor and materials, overhead costs, or other losses or expenses incurred by the Holder or any third party. Specifically excluded from Limited Warranty coverage are damage to the Units due to ordinary wear and tear, alteration, accident, misuse, abuse or neglect of the Units; the Units being subjected to vehicle traffic or other conditions which are not permitted by the installation instructions; failure to maintain the minimum ground covers set forth in the installation instructions; the placement of improper materials into the system containing the Units; failure of the Units or the septic system due to improper siting or improper sizing, excessive water usage, improper grease disposal, or improper operation; or any other event not caused by Infiltrator. This Limited Warranty shall be void if the Holder fails to comply with all of the terms set forth in this Limited Warranty. Further, in no event shall Infiltrator be responsible for any loss or damage to the Holder, the Units, or any third party resulting from installation or shipment, or from any product liability claims of Holder or any third party. For thls Limited Warranty to apply, the Units must be installed in accordance with all site conditions required by state and local codes; all other applicable laws; and Infiltrators installation instructions. (d) No representative of Infiltrator has the authority to change or extend this Limited Warranty. No warranty applies to any party other than the original Holder. The above represents the Standard Limited Warranty offered by Infiltrator. A limited number of states and counties have different warranty requirements. Any purchaser of Units should contact Infiltrator's Corporate Headquarters in Old Saybrook, Connecticut, prior to such purchase, to obtain a copy of the applicable warranty, and should carefully read that warranty prior to the purchase of Units. U.S. Patents: 4,759,661; 5,017,041; 5,156,488; 5,336,017; 5,401,116; 5,401,459; 5,511,903; 5,716,163; 5,588,778; 5,839,844 Canadian Patents; 1,329,959; 2,004,564 Other patents pending. Infiltrator, Equalizer, Quick4, and SideWinder are registered trademarks of Infittrator Water Technologies. Infiltrator is a registered trademark in France. Infiltrator Water Technologies is a registered trademark in Mexico. Contour, MicroLeaching, PolyTuff, ChamberSpacer, MultiPort, PosiLock, QuickCut, QuickPlay, SnapLock and StraightLock are trademarks of Infiltrator Water Technologies PolyLok Is a trademark of PolyLok, Inc. TUF-TITE is a registered trademark of TUF-TITS, INC. Ultra -Rib is a trademark of IPEX Inc. © 2013 Infiltrator Water Technologies, LLC. All rights reserved. Printed in U.S.A PLUS05 0713 Contact Infiltrator Water Technologies' Technical Services Department for assistance at 1-800-221-4436 PRESSURE PIPE IF REQ'D, PER DESIGN INFILTRATOR WATER TECHNOLOGIES QUICK4 PLUS STANDARD CHAMBER TYPICAL TRENCH DETAIL SECTION VIEW (NOT TO SCALE) NATIVE BACKFILL TOPSOIL 6" COVER (mi 12" COVER H -1G 34" (36" WIDE TRENCH) 12" SPACING PER CODE * LENGTH AND NUMBER OF TRENCHES DETERMINED BY DESIGN. 34" • 8" INVERT INFILTRATOR' INFILTRATOR WATER TECHNOLOGIES 4 Business Park R. Old Saybrook, CT 06475 (800) 221.4436 QUICK4 PLUS STANDARD CHAMBER TYPICAL TRENCH DETAIL SECTION VIEW Draw bv: EMB Date 05/20/2015 Scale: NOT TO SCALE Checked by, OFH Sheet 1 of 1 0renco® Orifice Shields Applications Orenco® Orifice Shields are used in a pressurized distribution system to protect the orifices from backfill debris that might cause orifice blockage. Orifice shield installed on lateral pipe, standard configuration Shield Orifice Cutaway view, standard configuration Orifice Shield Cutaway view, cold weather configuration General Orenco Orifice Shields snap -fit onto laterals. They may be placed on top of or beneath a lateral, depending on the location of the orifice. Orifice shields are covered by method -of -use patent # 5,360,556. Standard Models 0S075, OS100, 0S125, 0S150, 0S200 Product Code Diagram OSE 1 Lateral pipe size, nominal: 075 = 0.75 in. (20 mm) 100 = 1,00 in. (25 mm) 125 = 1.25 in. (32 mm) 150 = 1.50 in. (40 mm) 200 = 2.00 in. (50 mm) Orifice shield Material of Construction PVC per ASTM D-1784 Physical Specifications Model Shield U.D. Lateral pipe O.D. in. (mm) in. (mm) OS075 3.5 (89) 1.05 (27) 0S100 3.5 (89) 1.315 (33) 0S125 3.5 (89) 1.66 (42) 05150 4.5 (114) 1.90 (48) 05200 4.5 (114) 2.375 (60) Orenco Systems® Inc. , 814 Airway Ave., Sutherlin, OR 97479 USA • 800-348-9843 • 541-459-4449 • www.orenco.com NTD -SF -0S-1 Rev. 1.1, ® 09/14 Page 1 of 1 Iters# SEK- Orenco® Flushing Assemblies til Flushing Assemblies Orenco® flushing assemblies provide easy access for lateral maintenance. Flushing assembly kits include a PVC sweep with ball valve and a polyethylene valve box enclosure. Orenco® flushing assemblies are available in the following sizes: • 1" diameter • 1.25" diameter • 1.5" diameter • 2" diameter Valve Boxes Orenco® valve boxes are used to provide access to flushing assemblies. Constructed of polyethylene. Valve Box, 7 -in. diameter round enclosure Note: Kits include VB7 valve box enclosure. Vir VALLEY PRECAST inc. Water & Wastewater • Systems • Products • Service b OS (719) 395-6764 28005 County Road 317 P.Q. Box 925 Fax: (719) 395-3727 Buena Vista, CO 81211 Website: http://vaIleyprecast.com/ Email: frontdesk@valleyprecast.com