HomeMy WebLinkAboutCorrespondence from EngineerRe: 421 header
Mic Baca <studiom.engineer@gmail.com>
Wed 8/26/2020 12:18 PM
To: Darren Gallegos <darrengallegos@hotmail.com>
I need that osb to be on the same plane, so we will need to cut those 2x6's off at the top of door
and remove the 2x10 over the door, install the 1/2" osb, then reinstall the 2x6's and 2x10 where
you need them for your door spring. We can leave the 2x6's that wrap the door, because like
you said, they will be hard to remove and get a good finish there.
In terms of the osb joints, make sure we get the center of the osb sheet to center on the LVL
header....so you will have a joint 4 ft below the door and then 4 ft above the door.
Mic
On Wed, Aug 26, 2020 at 12:08 PM Darren Gallegos <darrengallegos@hotmail.com> wrote:
Mic,
We have a 2x6 around the interior side of the garage door for the garage door and track to
mount. It goes all the way to the ceiling on the sides and we have a 2x10" in the center. Could
we leave this and sheet around or should we remove to sheet with OSB?
Thanks,
Darren
Michael "Mic" Baca, P.E.
Studio M Engineers, LLC
250 Tripp Drive
Rifle, Colorado 81650
970_A66-8690 'sell
https://outlook.11ve.com!mail/0/search/!d/AQMkADAwATYwMARYWVkN...AAA%3D?RpsCsrfState=301ed271-9437-8cf5-adcf-3bOdb253b42b&nlp=1 Page 1 of 1
Re: LVL holes
Mic Baca <studiom.engineer@gmail.com>
Wed 8/19/2020 11:19 AM
To: Darren Gallegos <darrengallegos@hotmail.com>
we are fine with four 3/4" dia holes so long as they are in the center 3rd of the span.
On Wed, Aug 19, 2020 at 10:35 AM Darren Gallegos <darrengailegos@Wiotmail.com> wrote:
Hi Mic,
Here we go again.
Chart on site but still electrician didn't follow. We have 4 - 3/4" holes in center span. Chart
says we can have 2" holes but only 3 holes max. For now I told them to use 2 of them and we
may need a patch on the other 2 ?
Thanks
Darren
Michael "Mic" Baca, P.E.
Studio M Engineers, LLC
250 Tripp Drive
Rifle, Colorado 81650
970-366-8690 cell
https://outlook.live.com/mail/0/search/id/AQMkADAwATYwMAItYWVkN...2FCAAAA7RpsCsrfState=301ed271-9437-8cf5-adcf-3bOdb253b42b&nlp=1 Page 1 of 1
Re: 421 BCI
Mic Baca <studiom.engineer@gmail.com>
Thu 7/2/2020 8:12 AM
To: Darren Gallegos <darrengallegos@hotmail.com>
Sorry. They should be 2 span BCI 60's now.
On Wed, Jul 1, 2020 at 2:35 PM Darren Gallegos <darrengallegos@hotmail.cam> wrote:
Hi Mic,
Just double checking. Originally we had 14" BCI 6o's. Then without the storage it went to
BCI go's.
Now that the storage is back the plans show BCI go's still.
It that what you want?
Thanks.
Darren
Michael "Mic" Baca, P.E.
Studio M Engineers, LLC
250 Tripp Drive
Rifle, Colorado 81650
970-366-8690 cell
https://outlook.live.com/mail/0/search/id/AQMkADAwATYwMAItYWVkN...xRiAAAA?RpsCsrfState=301ed271-9437-8cf5-adcf-3bOdb253b42b&Np=1 Page 1 of 1