Loading...
HomeMy WebLinkAboutEngineer's Truss Fix Report 10.28.2022MiTek USA, Inc. 400 Sunrise Avenue, Suite 270 Roseville, CA 95661 Telephone 916-755-3571 MiTek USA, Inc. Re: The truss drawing(s) referenced below have been prepared by MiTek USA, Inc. under my direct supervision based on the parameters provided by Trusfab, Inc.. October 28,2022 Baxter, David Pages or sheets covered by this seal: R73302892 thru R73302892 My license renewal date for the state of Colorado is October 31, 2023. 9359 89 FOX PROWL IMPORTANT NOTE: The seal on these truss component designs is a certification that the engineer named is licensed in the jurisdiction(s) identified and that the designs comply with ANSI/TPI 1. These designs are based upon parameters shown (e.g., loads, supports, dimensions, shapes and design codes), which were given to MiTek or TRENCO. Any project specific information included is for MiTek's or TRENCO's customers file reference purpose only, and was not taken into account in the preparation of these designs. MiTek or TRENCO has not independently verified the applicability of the design parameters or the designs for any particular building. Before use, the building designer should verify applicability of design parameters and properly incorporate these designs into the overall building design per ANSI/TPI 1, Chapter 2. Design valid for use only with MiTek® connectors. This design is based only upon parameters shown, and is for an individual building component, not a truss system. Before use, the building designer must verify the applicability of design parameters and properly incorporate this design into the overall building design. Bracing indicated is to prevent buckling of individual truss web and/or chord members only. Additional temporary and permanent bracing is always required for stability and to prevent collapse with possible personal injury and property damage. For general guidance regarding the fabrication, storage, delivery, erection and bracing of trusses and truss systems, see ANSI/TPI1 Quality Criteria, DSB-89 and BCSI Building Component available from Truss Plate Institute, 2670 Crain Highway, Suite 203 Waldorf, MD 20601Safety Information WARNING - Verify design parameters and READ NOTES ON THIS AND INCLUDED MITEK REFERENCE PAGE MII-7473 rev. 5/19/2020 BEFORE USE. MiTek USA, Inc. 400 Sunrise Avenue, Suite 270 Roseville, CA 95661 Job 9359 Truss E4 Truss Type STUB STUDIO Qty 3 Ply 1 89 FOX PROWL Job Reference (optional) R73302892 8.430 s Aug 16 2021 MiTek Industries, Inc. Fri Oct 28 11:59:23 2022 Page 1 Trusfab Inc., New Castle, CO - 81647, ID:nOw1Ot6ijljIZQP4aciIHgypE3m-Lfn2ltXqFKhYoU9GVUJWqUWwkXTpffpQrhXYS3yOuMI Scale: 1/4"=1' A B C D E F G H I N M L K JOP Q R S T 5x6 5x6 3x4 4x6 5x8 4x8 4x6 7x10 6x8 3x6 8x10 2x4 7-5-8 7-5-8 10-10-4 3-4-12 14-6-8 3-8-4 22-1-0 7-6-8 -1-6-0 1-6-0 7-5-8 7-5-8 10-10-4 3-4-12 14-6-8 3-8-4 18-2-0 3-7-8 22-1-0 3-11-0 24-1-0 2-0-0 2-2-94-5-116-11-30-11-60-11-82-4-52.50 12 8.00 12 4.00 12 Plate Offsets (X,Y)-- [B:0-3-0,0-2-4], [D:0-3-0,0-2-12], [H:0-0-13,0-3-0], [L:0-6-0,0-4-4] LOADING (psf) TCLL (Roof Snow=40.0) TCDL BCLL BCDL 40.0 15.0 0.0 * 10.0 SPACING- Plate Grip DOL Lumber DOL Rep Stress Incr Code 2-0-0 1.00 1.00 YES IRC2015/TPI2014 CSI. TC BC WB Matrix-S 0.95 0.45 0.86 DEFL. Vert(LL) Vert(CT) Horz(CT) Wind(LL) in -0.17 -0.28 0.14 0.06 (loc) K K H K l/defl >999 >947 n/a >999 L/d 360 180 n/a 240 PLATES MT20 Weight: 140 lb FT = 20% GRIP 169/123 LUMBER- TOP CHORD 2x6 DF 2100F 1.8E BOT CHORD 2x6 DF 2100F 1.8E *Except* M-N: 2x4 SPF 2100F 1.8E, C-M: 2x4 WW Stud WEBS 2x4 WW Stud *Except* B-L,E-J: 2x4 SPF 2100F 1.8E SLIDER Right 2x4 WW Stud 2-3-4 BRACING- TOP CHORD Structural wood sheathing directly applied or 4-9-4 oc purlins, except end verticals. BOT CHORD Rigid ceiling directly applied or 10-0-0 oc bracing. REACTIONS. (size)H=0-5-8, N=0-5-8 Max Horz N=-155(LC 12) Max Uplift H=-221(LC 14), N=-226(LC 10) Max Grav H=1673(LC 20), N=1629(LC 31) FORCES.(lb) - Max. Comp./Max. Ten. - All forces 250 (lb) or less except when shown. TOP CHORD B-C=-3133/320, C-D=-3937/350, D-E=-2697/212, E-F=-2694/202, F-H=-2787/269, B-N=-1553/293 BOT CHORD C-L=-1140/146, K-L=-227/3151, J-K=-235/4080, H-J=-132/2108 WEBS B-L=-268/2903, C-K=-12/868, D-K=-635/58, D-J=-1743/249, E-J=-107/2336, F-J=-77/391 NOTES- 1) Wind: ASCE 7-10; Vult=115mph Vasd=91mph; TCDL=5.0psf; BCDL=5.0psf; h=25ft; B=45ft; L=24ft; eave=4ft; Cat. II; Exp C; Enclosed; MWFRS (directional) and C-C Exterior(2) -1-6-9 to 1-5-7, Interior(1) 1-5-7 to 14-6-8, Exterior(2) 14-6-8 to 17-6-8, Interior(1) 17-6-8 to 24-2-8 zone; cantilever left and right exposed ; end vertical left and right exposed;C-C for members and forces & MWFRS for reactions shown; Lumber DOL=1.33 plate grip DOL=1.33 2) TCLL: ASCE 7-10; Pf=40.0 psf (flat roof snow); Category II; Exp C; Fully Exp.; Ct=1.00 3) Unbalanced snow loads have been considered for this design. 4) This truss has been designed for greater of min roof live load of 20.0 psf or 2.00 times flat roof load of 40.0 psf on overhangs non-concurrent with other live loads. 5) This truss has been designed for a 10.0 psf bottom chord live load nonconcurrent with any other live loads. 6) * This truss has been designed for a live load of 20.0psf on the bottom chord in all areas where a rectangle 3-6-0 tall by 2-0-0 wide will fit between the bottom chord and any other members. 7) Bearing at joint(s) H considers parallel to grain value using ANSI/TPI 1 angle to grain formula. Building designer should verify capacity of bearing surface. 8) Provide mechanical connection (by others) of truss to bearing plate capable of withstanding 221 lb uplift at joint H and 226 lb uplift at joint N. APPLY 2 X 4 X 2.5' SPF/DF/SP NO.2 SCAB TO ONE FACE OF TRUSS AS SHOWN. ATTACH WITH (3) - (0.131" X 3") NAILS ALONG OVERLAPED WEB/CHORD. REPAIR: TRIM VERTICAL L-M 1/2" AS SHOWN. October 28,2022 PRODUCT CODE APPROVALSLATERAL BRACING LOCATIONIndicates location where bearings(supports) occur. Icons vary butreaction section indicates jointnumber where bearings occur.Min size shown is for crushing only.Indicated by symbol shown and/orby text in the bracing section of theoutput. Use T or I bracingif indicated.The first dimension is the plate width measured perpendicular to slots. Second dimension isthe length parallel to slots.Center plate on joint unless x, yoffsets are indicated.Dimensions are in ft-in-sixteenths.Apply plates to both sides of trussand fully embed teeth.1. Additional stability bracing for truss system, e.g. diagonal or X-bracing, is always required. See BCSI.2. Truss bracing must be designed by an engineer. For wide truss spacing, individual lateral braces themselves may require bracing, or alternative Tor I bracing should be considered.3. Never exceed the design loading shown and never stack materials on inadequately braced trusses.4. Provide copies of this truss design to the building designer, erection supervisor, property owner and all other interested parties.5. Cut members to bear tightly against each other.6. Place plates on each face of truss at each joint and embed fully. Knots and wane at joint locations are regulated by ANSI/TPI 1.7. Design assumes trusses will be suitably protected from the environment in accord with ANSI/TPI 1.8. Unless otherwise noted, moisture content of lumber shall not exceed 19% at time of fabrication.9. Unless expressly noted, this design is not applicable for use with fire retardant, preservative treated, or green lumber.10. Camber is a non-structural consideration and is the responsibility of truss fabricator. General practice is to camber for dead load deflection.11. Plate type, size, orientation and location dimensions indicated are minimum plating requirements.12. Lumber used shall be of the species and size, and in all respects, equal to or better than that specified.13. Top chords must be sheathed or purlins provided at spacing indicated on design.14. Bottom chords require lateral bracing at 10 ft. spacing, or less, if no ceiling is installed, unless otherwise noted.15. Connections not shown are the responsibility of others.16. Do not cut or alter truss member or plate without prior approval of an engineer.17. Install and load vertically unless indicated otherwise.18. Use of green or treated lumber may pose unacceptable environmental, health or performance risks. Consult with project engineer before use.19. Review all portions of this design (front, back, words and pictures) before use. Reviewing pictures alone is not sufficient.20. Design assumes manufacture in accordance with ANSI/TPI 1 Quality Criteria.21.The design does not take into account any dynamic or other loads other than those expressly stated.Failure to Follow Could Cause PropertyDamage or Personal Injury (Drawings not to scale)© 2012 MiTek® All Rights ReservedMiTek Engineering Reference Sheet: MII-7473 rev. 5/19/2020edge of truss.from outside"16/1-0ICC-ES Reports:ESR-1311, ESR-1352, ESR1988ER-3907, ESR-2362, ESR-1397, ESR-3282JOINTS ARE GENERALLY NUMBERED/LETTERED CLOCKWISEAROUND THE TRUSS STARTING AT THE JOINT FARTHEST TOTHE LEFT.CHORDS AND WEBS ARE IDENTIFIED BY END JOINTNUMBERS/LETTERS.W 4 - 6 W3-6W3 - 7 W2-7W1-7C1-8 C5-6C6-7C7-8C4-5 C3-4C2-3C1-2TOP CHORD TOP CHORD 87654321BOTTOM CHORDSTOP CHORDSBEARING4 x 4PLATE SIZEThis symbol indicates the required direction of slots inconnector plates."16/1For 4 x 2 orientation, locateplates 0- 1"4/3PLATE LOCATION AND ORIENTATIONSymbolsNumbering SystemGeneral Safety Notes *Plate location details available in MiTek 20/20software or upon request.Industry Standards:ANSI/TPI1: National Design Specification for Metal Plate Connected Wood Truss Construction.DSB-89: Design Standard for Bracing.BCSI: Building Component Safety Information, Guide to Good Practice for Handling, Installing & Bracing of Metal Plate Connected Wood Trusses.6-4-8WEBSTrusses are designed for wind loads in the plane of the truss unless otherwise shown.Lumber design values are in accordance with ANSI/TPI 1 section 6.3 These truss designs rely on lumber values established by others.dimensions shown in ft-in-sixteenths